Calcium aluminate cement in castable alumina: From hydrate bonding to the in situ formation of calcium hexaluminate

Calcium hexaluminate (CA₆) is an intrinsically densification-resistant material, therefore, its porous structures are key materials for applications as high-temperature thermal insulators. This article reports on the combination of calcined alumina and calcium aluminate cement (CAC) in castable aqueous suspensions for the in situ production of porous CA₆. The CAC content (10–34 vol%) and the curing conditions ensure structural integrity prior to sintering and maximize the development of hydrated phases. Changes in physical properties, crystalline phases, and microstructure were investigated after isothermal treatments (120–1500 °C), and three sequential porogenic events were observed. The hydration of CAC preserved the water-derived pores (up to 120 °C), and the dehydroxylation of CAC hydrates (250–700 °C) generated inter-particles pores. Moreover, the in situ expansive formation of CA₂ and CA₆ (900–1500 °C) hindered densification and generated intra-particle pores. Such events differed from those observed with other CaO sources, and resulted in significantly higher pores content and lower thermal conductivity.     

Microwave hybrid fast sintering of red clay ceramics

This work aimed to examine the performance of the hybrid sintering of clay ceramic in a microwave furnace, compared to the sintering process in a conventional furnace. The raw materials were subjected to X-ray fluorescence, loss on ignition (LOI), X-ray diffraction, particle size distribution, real specific mass, and thermogravimetric analyses. The red clay ceramic mass was prepared, extruded, pre-sintered in a conventional furnace at 600°C/60 min, and sintered at temperatures between 700 °C and 1100 °C. The sintering conventional (resistive oven) was carried out for 60 min with a heating rate of 10°C/min. In the microwave furnace, the sintering times were 5, 10, and 15 min, with a heating rate of 50°C/min, with a sintering chamber coated with silicon carbide (susceptor). The sintered specimens were characterized according to linear shrinkage, water absorption, apparent porosity, apparent specific mass, X-ray diffraction, Raman spectroscopy analysis, spectroscopy analysis in the ultraviolet and visible regions, microhardness, and scanning electron microscopy. The results showed that microwave sintering promoted an increase in the microhardness and apparent specific mass, and reduction in water absorption and apparent porosity values, due to greater densification in the microstructure. The best results occurred for specimens sintered at 1100°C.     

Environmentally Friendly Graphene Inks for Touch Screen Sensors

Graphene-based materials have attracted significant attention in many technological fields, but scaling up graphene-based technologies still faces substantial challenges. High-throughput top-down methods generally require hazardous, toxic, and high-boiling-point solvents. Here, an efficient and inexpensive strategy is proposed to produce graphene dispersions by liquid-phase exfoliation (LPE) through a combination of shear-mixing (SM) and tip sonication (TS) techniques, yielding highly concentrated graphene inks compatible with spray coating. The quality of graphene flakes (e.g., lateral size and thickness) and their concentration in the dispersions are compared using different spectroscopic and microscopy techniques. Several approaches (individual SM and TS, and their combination) are tested in three solvents (N-methyl-2-pyrrolidone, dimethylformamide, and cyrene). Interestingly, the combination of SM and TS in cyrene yields high-quality graphene dispersions, overcoming the environmental issues linked to the other two solvents. Starting from the cyrene dispersion, a graphene-based ink is prepared to spray-coat flexible electrodes and assemble a touch screen prototype. The electrodes feature a low sheet resistance (290 Ω □⁻¹) and high optical transmittance (78%), which provide the prototype with a high signal-to-noise ratio (14 dB) and multi-touch functionality (up to four simultaneous touches). These results illustrate a potential pathway toward the integration of LPE-graphene in commercial flexible electronics.     

An approach to torque and temperature thread by thread on tapping

During internal threading, small alterations in cutting parameters, tool geometry, or process characteristics produce considerable effects on torque and te     

Risk factors in software development projects: a systematic literature review

Software Quality Journal - Risks are an inherent part of any software project. The presence of risks in environments of software development projects requires the perception so that the associated...     

Azaaurones as Potent Antimycobacterial Agents Active against MDR- and XDR-TB

Herein we report the screening of a small library of aurones and their isosteric counterparts, azaaurones and N-acetylazaaurones, against Mycobacterium tuberculosis. Aurones were found to be inactive at 20 μm , whereas azaaurones and N-acetylazaaurones emerged as the most potent compounds, with nine derivatives displaying MIC₉₉ values ranging from 0.4 to 2.0 μm . In addition, several N-acetylazaaurones were found to be active against multidrug-resistant (MDR) and extensively drug-resistant (XDR) clinical M. tuberculosis isolates. The antimycobacterial mechanism of action of these compounds remains to be determined; however, a preliminary mechanistic study confirmed that they do not inhibit the mycobacterial cytochrome bc1 complex. Additionally, microsomal metabolic stability and metabolite identification studies revealed that N-acetylazaaurones are deacetylated to their azaaurone counterparts. Overall, these results demonstrate that azaaurones and their N-acetyl counterparts represent a new entry in the toolbox of chemotypes capable of inhibiting M. tuberculosis growth.     

Low-cost and high-performance 3D printed YBCO superconductors

High-performance YBCO 123 (YBa₂Cu₃O_7-x) bulk superconductor samples were produced using the 3D printing paste-extrusion technique. The YBCO powder obtained after sintering a pre-mixture of Y₂O₃, BaCO₃ and CuO powders at 950 °C was used in the formulation of pastes for extrusion in a 3D freeform printer. The 3D samples printed from pastes containing the pre-mixture powders were sintered, while those produced using the YBCO powder were not. X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) and Raman analysis all confirmed the YBCO phase after sintering, both in the powder and in the samples made with the pre-mixture. Scanning electron microscopy (SEM) images revealed powder grains of heterogeneous size and geometry, as well as grain aggregation, in the sintered samples. Superconducting quantum interference device (SQUID) measurements taken within a fixed magnetic range revealed that the printed pieces have a typical magnetization temperature of 92 K, reaching ?1.43 emu/g and ?1.59 emu/g respectively a zero-field-cooled magnetization (ZFC) for sintered and non-sintered printed samples.